Tank Bottom Remediation

Tank Bottom Remediation

poultry-litter384x90

Main Process Components

1. Feed System

Live bottom feeder, incline screw conveyor, knife gate airlock valves, kiln feed screw conveyor. More InfoThe hydrocarbon contaminated feed is placed in the feed hopper, which includes a live bottom feeder. This live bottom feeder is VFD controlled in order to meter the feed into the system. The feed exits the live bottom feeder and travels via the transfer screw conveyor to two double knife gate airlock valves. These airlocks prohibit the flow of outside air into the process chamber, allowing the feed material to be introduced into the primary thermal treatment unit into a completely oxygen deficient environment.

2. Discharge System

Knife gate airlock valves, discharge cooling incline conveyor. More InfoThe residual solids are cleaned to the customer's requested standard, typically determined by regulatory requirements. Residual solids are usually cleaned to less than 1000 H.C. PPM for refinery waste applications and 5000 H.C. PPM for drill cuttings. Residual solids leave the process chamber and are discharged into a solids cooling conveyor. This cooling conveyor is typically a hydration screw utilizing atomized water to cool the solids before being discharged.

3. Primary Thermal Desorption Unit

Indirect fired stainless steel rotary kiln with combustion chamber, gas or oil fired burners, gear drive powered by an electric motor. More InfoThis indirect fired rotary dryer has multiple zones, each with independent temperature controls. The drum is heated on the outside in order to maintain the integrity of the feed. Heat is transferred into the feed through conduction as the material is conveyed through the drum. The kiln operates in an oxygen deficient and slightly negative atmosphere. As the feed is heated, hydrocarbons, devolatized from the feed, are pulled out of the system in a counter-current direction to the material flow.

4. First Stage Oil Condenser

Oil condenser with tank, spray nozzle, cooling loop More InfoVapors from the thermal processor pass through an oil condenser. The oil condenser removes most hydrocarbons in the vapor stream. This recovered oil is cooled and pumped to the client's supplied storage tanks.

5. Second Stage Water Condenser

Water condenser with tank, spray nozzle, air cooled heat exchangers. More InfoAfter passing through the oil condenser, the vapor stream typically contains water vapor and very light hydrocarbons. This vapor is passed through a second stage water condenser in order to knock out water and other condensables

6. Oil Water Separator

Steel construction with float level. More InfoThe condensate from the second stage water condenser is pumped through a cooling loop and into an oil water separator, where residual oils are removed from the water.

7. Polishing Condenser

Mist eliminator and condenser with tank.

8. Thermal Oxidizer

Gas or oil fired burners and induced draft fan. More InfoThe non-condensable gases are pulled from the second stage by an induced draft fan and pushed into the thermal oxidizer.

Vulcan® Drying Systems Systems Tank Bottoms Detailed Specifications

Basis of Design - Throughput Calculations Based on - 50% Solids, 30% Hydrocarbons, 20% Water
ModelTonnageDrumPortable
TB3151 TPH3x15YES
TB4202 TPH4x20YES
TB4303 TPH4x30YES
TB5255 TPH5x25YES
TB6307.5 TPH6x30NO
TB73510 TPH7x35NO

* Varying capacities and feed consistency will change product capacity.

Additional Options

Heat Recovery

Using heat from a thermal oxidizer allows for preheating of combustion air in burners. This option can save up to 25% of fuel consumption in the system.

Waste Oil Burner System

An additional waste oil burner system consists of waste oil burners, fuel train, filters, and waste oil storage tank with heating elements. Reusing recovered oil as fuel will typically reduce fuel cost.

Discharge Quench

The stack on the discharge auger can be fitted with spray nozzles along the length of the stack. The quench spray removes excess particles from the gas stream before discharging steam into the atmosphere.

Nitrogen Generator

The swing adsorption nitrogen generator, with a nitrogen storage tank purges the system during start-up and shutdown. Nitrogen is also utilized during the process in order to keep O2 levels below the pre-detemined percent.

Portable

A portable option is available for some models, while the option of placing the entire system on skids is available for all models.

Learn More

Documents ( 4 )

OilfieldTechnology_Page_1

Cover Story: Oilfield Technology

OilGasShipping_Page_01

Cover Story: The Remediation of Drilling Waste

idr_brochure_Page_1

Indirect Fired Thermal Desorption Unit Brochure

Standard-TDU

Thermal Desorption Unit Process Flow Diagram your@email.com

Technologies ( 1 )

thermaldesorption

Thermal Desorption

Videos ( 7 )

manufacturing_marvels
Vulcan® Drying Systems

Manufacturing Marvels

baler_webVideo
Cram-A-Lot

DB 60 LU Vertical Baler

vulcan_tdu
Vulcan® Drying Systems

Thermal Desorption Unit Systems